In the flatform,finite element analysis is done on compressor valve plate.

在此平台上,对压缩机阀板进行了有限元分析。

The finite element models of axial tension member and eccentrical tension members are established with ANSYS finite element program.

4、用通用有限元分析软件ANSYS建立了混凝土轴心和偏心受拉的有限元模型，进行分析并得到了受拉构件的应力云图、变形图及开裂图，并与理论分析结果进行了比较。

By the equilong unit finite element method based on the Wenkel model, the computation is speeded up remarkably.

采用文克尔模型为基础的等长单元有限元法,显著地提高了计算速度。

The essay analyses free vibration problem of laying bed build-up board of antisymmetry angle with spline finite element method.

本文用样条有限元法,分析了反对称角铺设层合板的自由振动问题.

Based on this project, this paper has used the finite element method to analyze the similar isotrope rock slope with accumulative stratum.

本文以此工程为背景，对有堆积层的类均质岩体边坡的稳定性进行有限元模拟分析。

A class of nonconforming finite elements are applied to hyperbolic equation with semidiscretization on anisotropic meshes, the optimal error estimates are derived.

摘要在各向异性条件下，讨论了双曲型方程的一类非协调有限元逼近，给出了半离散格式下的最优误差佑计。

The finite element program design method has laid a solid foundation for in depth reseach of physical thoracic impedence rheogram wave form. ?

该程序设计方法为进一步深入研究人体胸腔阻抗血流图波形的成因打下了基础。

A reliable, feasible finite element analysis model for multi-pin-hole connected structure with multi-cracks was established with contact between pin and the conjunctional structure.

文中运用考虑销钉与结构板件间接触的有限元分析方法，建立合理的计算模型，为多孔多裂纹裂尖应力强度因子提供可靠、可行的分析途径。

Under the vertical loading condition, using three-dimension finite element analysis software investigated the stress of natural tooth, nichrome and rhotanium post inlay restoration teeth.

在垂直向加载的情况下,应用三维有限元分析软件分别对天然牙、镍铬合金、金钯合金带桩嵌体修复牙的应力进行分析。

As a qualitative analysis,finite element method gets a more satisfactory result in describing the propagation of the long wave of open channel unconstant flow.

作为一种定性分析，有限单元法对描述明渠非恒定流长波的传播给出了满意的结果。

A 3D finite element analytic model was established for the rapier driving system to investigate the structural features of its griper heads, belts and wheels.

摘要针对剑杆织机剑带、剑头、传剑轮的结构特点，建立了传剑系统三维有限元分析模型。

The analysis of the finite element method using th e axisymmetric model was employed to assess the mechanics behavior of the rubber toughening in mesostructure.

在细观结构上采用典型轴对称单元的有限元分析来预测增韧环氧树脂的力学行为。

A theory of aeroelastic stability of hingeless rotor blade in hover by using the Galerkin weighted residual finite element method is developed in this paper.

采用伽辽金加权余数有限元素法发展了一种悬停状态下无铰旋翼桨叶气弹稳定性的分析方法。

The finite element method is applied to prestressed slabs, the mechanical characters under the normal using load condition are analysised, with unconsidering the lateral restraints.

本文在结合某框架-核心筒结构无粘结预应力楼盖工程实例基础上,对侧向约束对预应力楼盖受力性能的影响做了初步的探讨。

In this paper, a comprehensive survey for the state of art of a posteriori error estimates in finite element computation for magnetostatics since 1980s is presented.

80年代以来,国际上兴起对恒定磁场后验误差估计的研究,本文系统地介绍这方面的发展概况。

Using the software of ANSYS, it was carried out nonlinear finite element analysis upon the basic behavior of high-strength concrete shear wall subjected to monodirectional lateral load.

摘要采用ANSYS软件对高强混凝土剪力墙在单向水平荷载作用下的受力过程进行了非线性有限元分析。

That we use finite element analysis calculate to the strength and the rigidity of the bodywork structure.Thus the optimum fillet of the small underframe structure can be specified.

采用有限单元法对小底架结构的强度、刚度、挠跨比进行了分析计算,为小底架设计提供了参考依据。

The contact between welding plate and fixture is treated as constraint in the finite element model of dynamic welding angular distortion simulation for overlayer in CO2 gas arc welding.

摘要采用有限元数值模拟方法研究了CO2气体保护堆焊的角变形动态过程。为了反映夹具和焊接件的接触状态，将夹具和焊件统一建立有限元模型。